Free Essay

Investigation of the Resistance of a Wire

In: Science

Submitted By zebranthony
Words 1588
Pages 7
Background

In this investigation I am going to investigate what affect the resistance of a wire.

Electricity flows in metals. Metal wires are made of millions of tiny metal crystals. Each crystal’s atoms are arranged in a regular pattern. The metal is full of ‘free’ electrons that do not stick to any particular atom. They fill the space between atoms in a metal. When these electrons move they create an electric current.

Conductors have resistance, but some are worse than others. The free electrons keep bumping into atoms. A wires resistance depends on four main factors which are:

Resistivity
The length of the wire
Cross sectional area
The temperature of the wire
I am going to investigate how the length of the wire affects the resistance. I have done a preliminary experiment to help me decide the best way to do my investigation. The results should also help me make a prediction.

Preliminary Investigation

Below are my results from the preliminary experiment (see table 1). I have taken three readings each from the Volts and current to make sure it is as accurate as possible

Table 1

From the results I can see that as the length of the wire increases, the resistance increases as well. Furthermore I have noticed that if you double the length of the wire, the resistance is roughly doubled. E.g. when the length of the wire is 20cm the resistance is 3.14 ohms, when the length of the wire is 40cm the resistance is 6.18 ohms which is roughly double 3.14 ohms. In my main investigation I will see if this theory applies to my results.

I found that the apparatus I used was suitable but I think that I could possibly increase the range of my results to obtain very reliable results, perhaps maybe increasing the length of the wire by 5cm each time instead of 10cm.

Investigating the resistance of a wire

Aim

I am going to investigate the resistance of a wire in relation to its length.

Prediction

I predict that the longer the wire the larger the resistance. This is because the free electrons in the wire have to bump into more atoms and therefore, it is harder for electricity to flow. Similarly, the shorter the wire the smaller the resistance because there will be less atoms for the electrons to bump into and so, it will be easier for the electricity to flow. Furthermore, the resistance of a wire is directly proportional to the length and inversely proportional to the area, so doubling the length of a wire should increase the resistance by a factor of two. This is because if the length of the wire is doubled, the electrons bump into twice as many atoms so there will be twice as much resistance. If this is correct the graph will show a positive correlation which is what I expect.

Apparatus

The apparatus I will be using in this experiment is as follows:

1 ammeter (to measure current)
1 voltmeter (to measure voltage)
5 x wires
2 crocodile clips
Power pack
100cm nichrome wire
Method

Firstly I will collect the apparatus I need and set it up as shown in the diagram below. Next I will set the power pack on as low voltage as possible to ensure that there is not too high a current passing through the circuit (which could potentially affect the results because the wire will get too hot).

I will place one crocodile clip at 0cm on the wire and the other at 5cm to complete the circuit. I will then turn the power pack on and record what the voltmeter and ammeter read. I will switch off the power pack, move the crocodile clip that was at 5cm up to 10cm and switch on the power pack. Again I will record what the voltmeter and ammeter read and turn off the power pack. I will repeat this method every 5cm until I get up to 100cm, taking three readings from both the voltmeter and ammeter each time to ensure it is a fair test. Also after each reading I will switch the power pack off to ensure that the wire doesn’t get too hot and affect my results.

Fair Test

To ensure it is a fair test I will record the voltage and the current three times every 5cm and take the average reading. This will ensure that there are no false readings and will also cancel out any anomalous results. I will also ensure that the wire does not heat up too much by firstly making sure that I do not set the voltage too high on the power pack and keep it the same for every reading, and secondly, making sure that I turn the power pack off after each reading. I will try and make this investigation as accurate as possible.

Variables

There are different variables which can be changed in this experiment – the independent variable. I am however, due to my line of enquiry, only going to change the length of the wire. The variables I will control will be the type of wire (resistivity) and the cross sectional area of the wire. I will also control, using the power pack, how many volts pass through the wire in the first place. Below is a table illustrating the effect of changing the variables.

Safety

I will ensure the experiment is safe by making sure that all the wires are connected properly and that none of the insulation on the wires is worn. I will also ensure that there is a clear indication that the power is isolated by means of a switch and a L.E.D. I will stand up during the investigation to ensure that I do not injure myself if something breaks.
From the table above I can see that as the wire increases in the length the resistance increases to. This shows that the first part of my prediction that, ‘the longer the wire the larger the resistance’ was correct.

Also my theory that doubling the length of the wire increases the resistance by a factor of two is correct:

The table (table 4) to the right illustrates this:

Graph

I will make a graph to illustrate my results and so I can further analyse my results.

(make a graph from the table of your results)

...if the results are similar to those above...your graph should follow the same pattern as the statement below...

"The graph is almost a straight line and has a positive strong correlation which shows that, as the length of the wire increases the resistance gets bigger. It also shows that my results were consistent and that my prediction, “the resistance of a wire is directly proportional to the length and inversely proportional to the area, so doubling the length of a wire should increase the resistance by a factor of two,” was correct."

I am going to take a sample from my results and draw a graph to show error bars. I cannot use all the results because I have to enlarge the scale in order to illustrate the error bars

Evaluation

Overall I think that my results are very consistent. Most of the points were on, if not close to the line of best fit. There are a few points which are further away from the line of best fit than the others, but they still fit in with the general trend. There are no anomalous results which I would consider to be far away from the line of best fit.

There are possible sources of error which might have lead the results to be inconsistent such as a kink in the wire. This would have prevented the area of the wire from remaining constant and would have affected my results. However I made sure that the wire remained straight throughout the experiment.

I think that the range of my results was sufficient enough for me to make a valid conclusion about how the length of the wire affected the resistance. This was because I could plot a graph and show the general trend.

I think that the pattern/general trend would continue beyond the range of values I used. However, I think that unless I had specialist equipment the results would be distorted because the wire would eventually get very hot. Also, the apparatus I had use of in the school would not be suitable if I were to keep increasing the length of the wire, e.g. in a classroom environment I could not increase the length to more than 150cm because of the safety factor and minimal space.

I think my method could have been improved to make my results even more consistent. I could perhaps consider using the same type of wire but a different piece of wire each time. This would prevent one wire getting hot and affecting the results. However this would have been impractical and would waste a lot of time which I did not have in a lesson. Overall I think my method was very good in obtaining reliable results.

To support my prediction and conclusion I could do further experiments such as using a different types of wire instead of just nichrome and observing to see if the same theory applied to the results. I could also consider using different cross-sectional areas of wires or even change the temperature of the wires deliberately and see how it affected the resistance of the wire…...

Similar Documents

Free Essay

Resistance of a Wire

...metal wire, together with the physical dimensions of the wire, from which you will calculate the resistivity of the metal. Theory The resistance R of a component in a circuit is given by the equation V = IR where V is the potential difference across the component and I is the current in the component. The resistance of a wire is given by the equation R = ρl / A where ρ is the resistivity of the metal from which the wire is made, l is the length of the wire and A is its cross-sectional area. Using the circuit below, you will make measurements of current and voltage for different lengths of wire. You will plot a graph of resistance against length and from this you will calculate the resistivity. A V flying lead zero end of the metre rule tape to hold wire into place resistance wire 70 © University of Cambridge International Examinations 2006 Teaching AS Physics Practical Skills Resistivity of a wire Student Worksheet Making measurements and observations Use the micrometer screw gauge to measure the diameter d of the resistance wire in several places along the length. Each time you take a measurement at a new place, rotate the wire slightly. 1 Tape the wire to the metre rule so it cannot slip and the markings of the rule are visible. 2 Connect the circuit shown in the diagram above. The flying lead should have a bare conducting end and should be long enough to touch any part of the resistance......

Words: 802 - Pages: 4

Premium Essay

Ethernet Wire

...corresponding slots on the top row of slots on connector. Try not to untwist the wire, since the Ethernet standard requires the wires stay twisted down to the last 1/2 inch. ETHERNET CABLE: COLOR-CODE STANDARDS The information listed here is to assist Network Administrators in the color coding of Ethernet cables. Please be aware that modifying Ethernet cables improperly may cause loss of network connectivity. Use this information at your own risk, and insure all connectors and cables are modified in accordance with standards. The Internet Centre and its affiliates cannot be held liable for the use of this information in whole or in part. T-568A Straight-Through Ethernet Cable The T-568A standard is supposed to be used in new network installations. Most off-the-shelf Ethernet cables are still of the T-568B standard; however, it makes absolutely no functional difference in which you choose. © CPH Solutions 2006 www.CPHSolutions.com Chuck Hauge T-568B Straight-Through Ethernet Cable Both the T-568A and the T-568B standard Straight-Through cables are used most often as patch cords for your Ethernet connections. If you require a cable to connect two Ethernet devices directly together without a hub or when you connect two hubs together, you will need to use a Crossover cable instead. RJ-45 Crossover Ethernet Cable A good way of remembering how to wire a Crossover Ethernet cable is to wire one end using the T-568A standard and the other end using the......

Words: 1012 - Pages: 5

Free Essay

What Factors Affect the Resistance of a Wire?

...Year 11 Physics Investigation- What factors affect the resistance of a wire? Introduction We are trying to find out if the thickness of a wire affects the resistance of a wire and also how it will do that. One reason I chose this investigation was because human reaction time is eliminated by not using the parachute method (the parachute experiment is to find out the factors affecting the rate of decent of a parachute), because you have to measure the timings on it by the eye and hand pressing the stop button and there could be some inaccuracies in this. In the test I am doing there is no space for human error because all the measuring is done by equipment and machines so all I have to do is make sure I use them properly and read them with accuracy. The wire resistance experiment is more precise because the equipment I will use to measure all sorts of different factors in the experiment is more precise than in the parachute experiment mainly because everything is still and not moving in the resistance experiment. We have chosen to do the thickness of the wire because it is easy to control and keep accurate because of the micrometer, which is very precise. In the parachute investigation I would have to measure the distances with a ruler and the micrometers precision is 0.01mm which is a very high precision whereas the ruler has a lower precision of 1mm. We could have used the material as a variable but when we get a graph of results it will be a bar......

Words: 1998 - Pages: 8

Premium Essay

Resistance of a Wire

...through is an insulator. Conductors intended to have resistance are called resistors (symbol ) Voltage- given the symbol V, measured in volts using a voltmeter Current- given the symbol I, measured in Amperes using an ammeter Metallic structure diagram Resistance Resistance is the ability to prevent or resist the flow of electrical current. Resistance occurs in an electrical circuit because of a collision between electrons and atoms, which slows the electrons down and converts some of their KE to heat energy. Resistance is measured in Ohms (Ω). Diagram Arrow shows direction of electron movement through the wire. Equation [pic] Factors which affect resistance Length of wire – this is being investigated Thickness of a wire – in a thin wire there are more possible paths for the electrons to pass through, therefore more electrons can flow through at one time, this increases the current which increases the resistance. Material of wire - wires of different densities will block more or less electrons Temperature - the vibration of warm molecules makes them more likely to collide with electrons, and resistance increases with temperature. Variables Independent- length Dependent - Voltage, current to measure, resistance Controlled - Temperature, material of wire, cross sectional area Circuit diagram Method 1. set up apparatus as shown above 2. measure out a 1m length piece of wire and connect it to the crocodile......

Words: 927 - Pages: 4

Premium Essay

Resistance

...Employees often show resistance to change due to fear of the unknown. When employees are accustom to their ways of doing things, new procedures or ideas may make them feel uneasy. In order for a company to stay up float, it is inevitable for changes to occur. Companies over the years have elaborated multiple tactics to turn resistance into collaboration. One popular way to avoid resistance within the organization is participation. Participation makes employees and upper management feel involved. Because design requires information from all participants, cooperation keeps everyone committed to the change. For example, a company decides to implement staggering work shifts effective immediately to improve logistics for the work place; however, employees show resistance given that they were never consulted or involved in such decisions. Participation can also be time consuming, so different approaches may be necessary. Even though coercion is the most commonly use approach for change implementation, it is not the best tactic as employees feel like victims. Coercion could even complicate or prolong change. In some instances, coercion may be optimal for rapid results in urgent matters. A good example for coercion could be a board of directors terminating the CEO for a terrible performance. Communication and education may be the most expensive approach to implement changes as it may require huge amounts of training and communication. Nevertheless, it is the most......

Words: 402 - Pages: 2

Free Essay

Wire Extraction

...WIRE DRAWING Objective To know how copper and aluminum drawing is done, and also to understand the machine setting and how the machine operates. Introduction Wire drawing is the process by which a metal rod is forced through a series of varying cross section die(s) and hence the metal rod cross sectional area is varied so as to obtain the desired shape and size. In Kenwest cables company their are 3 wire drawing machines namely:- 1. M55 2. H20 3. M85 1.M55 This is the main copper drawing machine and the one which can handle the 1st drawing process which is hard drawing. The raw material used is usually copper rod of 7.9mm thickness as the hard drawing material. The M55 can also handle further copper drawing like the H20. Operation procedure The M55 has several units namely:- a) stand b) block c) drawing basin d) annealer e) spooler a) stand It is responsible in guiding the copper rod being fed to the block or drawing basin. If its hard drawing its fed to the block but when its further drawing its directly fed into the drawing basin. This is because at the block section the die obtained may have a larger diameter than the copper rod in the case of further drawing hence the block is not required. b) Block It is functional when hard drawing takes place. The 1st die is usually located in this section (the block section) hence drawing process begins at the block section. The copper rod being fed is usually about 7.9mm in diameter which is the diameter...

Words: 3959 - Pages: 16

Premium Essay

Investigation

...existence that proved highly effective and efficient for business firms. “Social media marketing is the process of gaining website traffic or attention through social media sites. Social media marketing programs usually center on efforts to create content that attracts attention and encourages readers to share it across their social network” (Wikipedia, 2014). As said by Nielsen’s (2011), State of the Media: Social Media reports that 70% of social media users are engaged in online shopping (Nielsen, 2011).Consumers can access any site and get their needs fulfilled from any part of the world. Multi-national companies such as Apple, Samsung etc. have taken advantage of the growing opportunities in the field of social media marketing. This investigation focusses on the topic advantages and tools of social media marketing for various business firms. Social media marketing proves advantageous in providing a competent for companies that include social media marketing within their marketing strategies , one of the major advantage of social media marketing is the cost effectiveness , companies can communicate their ideas to large wide spread community all over the world in a minimum cost , this not only reduces the overall costs but also helps companies understand the consumer behavior and feedback of variety of consumers towards their respective product or service that they are providing which can help them innovate and improve the existing product or service, . Social media......

Words: 796 - Pages: 4

Free Essay

Investigating the Resistivity of a Wire

...the length of the wire affects the wires resistance. Also measuring the voltage and current. A thin and a thick wire are used to get the results needed. There are three factors that influence the resistance of w wire which are, the thickness of a wire, temperature and length. Knowing those factors and measuring them will show how the experiment went. Introduction: ------------------------------------------------- The resistance of a material is the extent to which is oppose the flow of current. “Electronics for today or tomorrow, 2nd Edition, Tom Duncan, page 8” Where as conductors have low resistance and inductors have high resistance. Further more resistance is measures with ohms. The main concept of the experiment is to investigate the difference in the resistance when having several lengths of a wire. The reason why different lengths of a wire affect the resistance is because the length of the will is increased which will also make the resistance increase as well, therefore electrons will have a longer distance to travel. Because of this the length of a wire should be proportional to the resistance. Conductors are good metals of electricity because they have low resistance which is why electrons get away easily just by applying the voltage. Furthermore, the resistance of a wire and the length of the wire both increase but the thickness of the wire decreases at the same time. Moreover, thin wires have high resistance but thick wires have low resistance. Due to Ohm’s law......

Words: 589 - Pages: 3

Free Essay

Man on Wire

...Man on Wire Imagine walking on a wire between the two of the tallest buildings in the world. This is exactly what a group of people plan to do with Philippe petit. The plan, consisted in braking into the twin towards and settle their equipment to connect both towers with a wire. Once everything was set petit, begin his journey walking on a rope thousands of feet above ground. As his journey ended, the police were waiting to punish him and his collies. Once the police got a hold of them, petit was giving a light punishment while his collies were expel from the country. In the film Man on wire, Philippe Petit and his friends plan to break into New Yorks twin towards to accomplish their dream goal. They knew it was not going to be easy, so they found ways to snick in and to get the measurement done before they accomplish something that has not been done. Petit and his friends knew that by trespassing was a sign of braking the law, but they did not had in mind that there were putting their lives at risk. For instance, what if Philippe Petit fell from the wirer or his friends fell down the building by setting down the tools they needed which will cause to hurt other people. They never saw it that way because they were too anxious to accomplish their goal. If they could break the law, why can’t I break the law the same way they did by using public space without permission? Philippe Petit and his group of friends were arrested and were given different punishments. In fact,......

Words: 590 - Pages: 3

Free Essay

Wire

...2014 Annual Report March 23, 2015 To Our Stockholders: You are cordially invited to attend the annual meeting of stockholders to be held on Tuesday, May 5, 2015 at 9:00 a.m., central time, at the corporate office of Encore Wire Corporation located at 1329 Millwood Rd., McKinney, Texas. The purposes of the meeting are to elect directors for the ensuing year, ratify the appointment of auditors for 2015, to approve, in a non-binding advisory vote, the compensation of the Company’s named executive officers and conduct other business that may properly come before the meeting. Net sales for the year ended December 31, 2014 were $1.167 billion, while net income for the year was $37.1 million, with fully diluted net earnings per common share of $1.78. Unit volume, measured in copper pounds contained in the wire sold increased 3.6% in 2014 versus 2013. Our new aluminum building wire plant finished its second full year of operations, during which we sold $103.4 million of aluminum building wire. We believe that our ability to sell aluminum wire has resulted in increased copper wire sales as customers prefer to “one-stop shop” and order enough pounds to get free freight. Aluminum demand is so strong that we are expanding the current 200,000 square foot aluminum plant with a 250,000 square foot addition. We believe that our costs are as low, or lower, than our competitors. We believe our superior order fill rates continue to enhance our competitive position, as our......

Words: 21591 - Pages: 87

Premium Essay

Resistance to Change and Overcoming Resistance

...RESISTANCE TO CHANGE AND OVERCOMING RESISTANCE This paper examines organizational change, focusing on the distinction of changes according to their scope and presenting a typology of evolutionary and strategic changes. Through empirical research, it analyzes the importance of the sources of resistance to change defined theoretically, also considering types of changes, offering hints about where organizations should pay special attention when initiating a change process. INTRODUCTION Many authors (Lawrence, 1954; Maurer, 1996; Strebel, 1994; Waddell and Sohal, 1998, among others) stress that the reasons for the failure of many change initiatives can be found in resistance to change. Resistance to change introduces costs and delays into the change process (Ansoff, 1990) that are difficult to anticipate (Lorenzo, 2000) but must be taken into consideration. Resistance has also been considered as a source of information, being useful in learning how to develop a more successful change process (Beer and Eisenstat, 1996; Goldstein, 1988; Lawrence, 1954; Piderit, 2000; Waddell and Sohal, 1998). Undoubtedly, resistance to change is a key topic in change management and should be seriously considered to help the organization to achieve the advantages of the transformation. THEORETICAL FRAMEWORK Organizational change is an empirical observation in an organizational entity of variations in shape, quality or state over time (Van de Ven and Poole, 1995), after the deliberate introduction of...

Words: 1310 - Pages: 6

Premium Essay

The Resistance

...infection can be easily contracted if not careful. Locker rooms are fertile breeding grounds for bacteria due to close quarters and the sharing of personal items. “In 2003, eight players from the St. Louis Rams football team contracted MRSA. The same year, linebackers Junior Seau of the Miami Dolphins and Ben Taylor of the Cleveland Browns had to be hospitalized because of the illness” (Watson 12). The fact that almost anyone is susceptible to superbugs should promote user knowledge and compliance. “The reality is, for now, humans will have to coexist with superbugs. These drug- resistant bacteria won’t disappear overnight” (Watson 52). Although its unfortunate, scientists wont be able to slow down and control the process of resistance until doctors are given more training in prescriptions, regulations and government actions are set to correct and enhance drug quality and supply around the world, and our population as a whole becomes aware of the problem and unites to achieve a less- resistant microbe world. Until then scientists are hard at work to keep up with the bacteria in what seems to be futile. Although this is true many people believe in achieving what was achieved many years ago, when Penicillin came to existence....

Words: 1007 - Pages: 5

Premium Essay

Investigation

...Jamel Vilmont 10/26/15 Investigation #3 Analyzing Evidence 1. The solvents are the three sample, Water, Hexane and Ethanol used. The sample are the coo laid used which was red blue and yellow and the markers used which was orange, blue, black, red, and green. 3. The solvent of water mixed with the Kool-Aid created a mixed color of red and yellow for the red Kool-Aid and high streak for the blue Kool-Aid and a disappearance of the yellow Kool-Aid. With markers dipped in ethanol, it created a yellowish orange streak, s short blue streak with little bit of red at the top and a long black streak. 4. the two that I found very similar in my experiment was the H2O blue Kool-Aid with similar features as the blue ethanol. The H20 orange, blue and black markers with the hexane orange blue and black markers as well. Interpreting Evidence 1. from my results we come to a conclusion that the Kool-aid where more soluble in water while the markers weren’t. 2. the one with the highest number of components was the read kool-aid that was dipped in water and the orange and blue markers that was dipped in ethanol. No matter what the Kool-Aid reacted the most to each solvent Making Claims All the markers acted differently with in water, ethanol and hexon and all the coolaids acted the same way excepted with ethanol but for all of the yellow Kool-Aid, they all acted the same....

Words: 258 - Pages: 2

Free Essay

Resistance

...The term resistance to change simply means that individuals are set in his or her ways and often don’t want to modify his or her routing. However, this change resistance doesn’t just occur when individuals who like their jobs are asked to make a change. Resistance even happens when individuals are chronically upset with their working conditions. For them, the known evil is preferable to the unknown. For anyone to resist a change, there obviously has to be a change. These new conditions are the events that occur around us every day. And these events, big or small, good or bad, invariably lead to some result. However, it is important to distinguish between the symptoms of resistance to change, and the causes behind it. These behaviors fall into two categories -- active-resistance or passive-resistance. Symptoms of active resistance occur where individuals are taking specific and deliberate action to resist the change. It may be overt, with such as public statements and acts of resistance, and it may be covert, such as mobilizing others to create an underground resistance movement. Overt active resistance, although potentially damaging, is at least visible and you have the option of using formal disciplinary actions (although more positive methods should normally be used first). When it is covert, you may also need to use to covert methods to identify the source and hence take appropriate action Passive resistance occurs where people do not take specific actions. At meetings...

Words: 692 - Pages: 3

Free Essay

The Wire

...introduces two major groups of characters: the Baltimore police department and a drug dealing organization run by the Barksdale family. The season follows the investigation of the latter over its 13 episodes. An investigation into a large Baltimore based drug dealing is triggered when detective Jimmy McNulty meets privately with judge Daniel Phelan following the acquittal of D'Angelo Barksdale for murder after a key witness changes her story. McNulty tells Phelan that the witness has probably been intimidated by members of a drug trafficking empire run by D'Angelo's uncle, Avon Barksdale, having recognized several faces at the trial, notably Avon's second-in-command, Stringer Bell. He also tells Phelan that nobody is investigating Barksdale's criminal activity, which includes a significant portion of the city's drug trade and several unsolved homicides. Phelan takes issue with this and complains to senior Police Department figures, embarrassing them into creating a detail dedicated to investigating Barksdale. However, owing to the department's dysfunctionality, the investigation is intended as a façade to appease the judge. An interdepartmental struggle between the more motivated officers on the detail and their superiors spans the whole season, with interference by the higher-ups often threatening to ruin the investigation. The detail's commander, Cedric Daniels, acts as mediator between the two opposing groups of police. Meanwhile, the organized and cautious Barksdale......

Words: 528 - Pages: 3

GTA Vice City Storyline in Hindi 7:24 | Tatouages, body art | V88 Android 6.0 Smart TV BOX 4K Latest RK3229 Quad Core 8GB HD 1080P WIFI Media$25.99 7d left