Premium Essay

Mechanics of Materials: Lab #1 Tension Test

In: Science

Submitted By burnsie44
Words 982
Pages 4
Tension Test

[pic]
(Fractured Copper Specimen)

By: Christl Burns

Mechanics of Materials Sec. 4

Lab Preformed on: 2/9/12

Introduction
The tensile test was preformed on the following commonly used materials; 836 Cold Rolled Steel, T351-2024 Aluminum, 110 Copper, Grey Cast Iron, and HDPE Plastic. The first objective was to examine the stress-strain curves in order to calculate and identify the significant mechanical properties of these materials. The curves are also used to give a better understanding of what these mechanical properties mean. The second objective was to compare the mechanical properties and physical appearance of these materials. In order to get the stress-strain curves, each specimen was placed in the tensile testing apparatus. The load frame slowly stretches the specimen until it breaks. The extensometer, was placed directly on the specimen and was hooked up to a computer program that collected all of the data, which was used to make the stress-strain curves.

Procedure
First a punch was used to mark off a two inch section on each specimen. This section was marked off so that it could be used as a reference in finding the elongation of the specimen.Then, using a caliper, the diameter of each was measured and recorded. Now the mechanist calipers were set up in increments of 0.05 inches starting at 2.05 inches. Next the specimen was loaded into the tensile testing apparatus, the extensometer was put onto the specimen, and the data-acquisition program was turned on. The extensometer had to be taken off the specimen once it has reached its proportional limit. Once it was taken off the mechanist calipers were used. As soon as the length in between the two marks on the specimen lined up with the caliper length the data for the live load was recorded. This was done until the material fractured. Next the two halves were removed from…...

Similar Documents

Free Essay

Torsion Test Lab Report

...Lab 1: Tension Test Andrew Thiher 2/17/2012 Introduction: In this lab, we tested the material properties of 836 cold rolled steel, T351-2024 aluminum, 110 copper, grey cast iron, and high-density polyethylene (HDPE) by subjecting each material to a tensile force until it fractured. Using data gathered, we graphed the stress-strain graph and determined specific properties for each material. These properties included whether the specimen was ductile or brittle, yield stress, and tensile strength. For equations used, see appendix 2. Experimental Apparatus: Each material was prepared for the experiment by marking the initial length as two inches by means of a gage punch and hammer. Additionally, calipers were used to measure the initial diameter. The sample was then screwed into the tensile testing machine and an extensometer was attached to measure elongation and collect data. The extensometer remained attached until the material reached its proportional limit, at this point it was removed, and the remaining data was collected using machinist scales prepared in .05 inch increments. Each time the gauge length reached the preset machinist scale increment, the live load from the computer was recorded. This process was repeated until the specimen fractured. Once the specimen fractured, the final gauge length and smallest diameter in the necking region were recorded. Calculations: [pic] |Property |Cold Steel |110...

Words: 1379 - Pages: 6

Free Essay

Mechanics and Materials Measurement and Error Lab

...EML3012C – Lab #1 Measurement, Instrumentation, Statistics and Error Group 1A Lab Performed: 9-5-2012 Report Submitted: 10-11-2012 Table of Contents: I. Motive…………………………………………………………….…………….iii II. Experimental…………………………………………………………………..iv III. Results/Discussion ………………….………………….…………..…….v-viii Part 1 Data…………………………………………..………………………….......v Part 1 Histogram……………………………………...……………………………vi Part 1 Calculations…………………………………...………………………….v-vi Part 2 Data summary……………………………………..…………………….…vii Part 2 Calculations……………………………………….………………………viii IV. Conclusion…………………………………………………………………….ix V. Appendix…………………….……………………………………………...x-xii I. Motive: The purpose of this lab is to analyze the error and deviation of manmade and manufactured objects. Measuring the marbles 100 times gives a population. The block’s dimensions (length, width, height) were measured 20 times each. This gives a sample for each dimension. From the population and samples, a histogram can be made of the data. Additionally, from these mean, mode, median, and standard deviation can be calculated. Lastly, the error and error propagation must be included because there is human and instrumental error. II. Experimental: This lab had two parts. For the first part, 100 glass spheres were measured. The A spheres were used. In the second part, the......

Words: 1468 - Pages: 6

Premium Essay

Materials Test 1 Review

...Chapter 1 – Materials Engineering Concepts * 1.1 Economic Factors * Availability and cost of raw materials * Manufacturing costs * Transportation * Placing * Maintenance * 1.2 Mechanical Properties * Loading conditions * Static load – A sustained loading of the structure over a period of time * Dynamic load – A load that generates a shock or vibration in the structure (periodic – repeats itself with time, random- load pattern never repeats, or transient- impulse load applied over short interval) * Dead load- Static load, always applied (weight of the structure) * Live load- Dynamic loads, (people in a building or movable objects) * Stress-Strain Relations * Stress : σ=FA (psi, ksi, kPa, MPa, GPa) * Strain: ε=Change in LengthOriginal Length (%, in/in, mm/mm) * Elastic behavior * Elasticity- instantaneous response (deformation to load) and must return to its original shape when the load is removed. Stretches the bonds between atoms-doesn’t change arrangement of atoms * Young’s Modulus (Modulus of Elasticity)- Slope of the linear portion of the stress-strain curve E=σε * Poisson’s ratio- Ratio of the lateral strain to the axial strain (must be between 0.0(compressible material)-0.5(does not change volume when load applied)) Usually between 0.1 and 0.45 ν=-εlεa * Generalized Hooke’s Law *......

Words: 1916 - Pages: 8

Free Essay

Lab 1

...NT1430 Linux Administration LAB 4 vi -- again On your linux server enter the following in the command line: root@servername: cd /opt root@servername: ls -la 1) Write what files exist in your directory. root@servername: touch sysinfo root@servername: ls -la 2) Write what files exist in your directory. 3) What are the permissions on the file you have just created? root@servername: chmod 755 sysinfo root@servername: ls -la 4) What are the permissions on the file you have just created? 5) What have you just done? Practical Mysystem root@servername: vi mysystem Now to enter into insert mode (edit mode) hit [i] to exit back into command mode hit [Esc] Now while you are in INSERT MODE type the following, be careful of all characters and typos. #!/bin/bash clear printf "This is information provided by mysystem.sh. Program starts now.\n" printf "Hello, $USER.\n\n" printf "Today's date is `date`, this is week `date +"%V"`.\n\n" printf "These users are currently connected:\n" w | cut -d " " -f 1 - | grep -v USER | sort -u printf "\n" printf "This is `uname -s` running on a `uname -m` processor.\n\n" printf "This is the uptime information:\n" uptime printf "\n" printf "That's all folks!\n" To end and save the file enter the following: [Esc] [:] You will exit Insert Mode and enter into Command Mode then save and exit vi: wq [Enter] Now run the script. root@servername: chmod 755 mysystem root@servername: ./mysystem Print a screen shot of the......

Words: 1450 - Pages: 6

Free Essay

Lab 1

...Lab One: Design a Research Project Hypothesis: Jewelweed juice speeds up healing of the rash caused by Western Poison Ivy. Research Proposal: This study is extremely valuable for the sole and simple reason that approximately 85 percent of the population will develop an allergic reaction if exposed to poison ivy, or poison oak according to the American Academy of Dermatology. As a researcher for a pharmaceutical company, this information will aid in the validity of the claim and marketing of the product. This research will also benefits humanity in general by providing a safe and effective cream as an aid in the healing process after exposure. Ten subjects will be selected after careful interviews regarding allergies to food, medication, or anything else. A thorough medical history review will be made to ensure healthy individuals participate. Any subject with history of severe allergic reactions of any kind will not be allowed to participate. Subjects cannot not be taking any medications or have signs or symptoms of illness at the start of experiment. Baseline vital signs and blood test will be performed: CBC & Chem 10. The subjects must be able to commit for a period of 21 days, and should not be claustrophobic. The age group will be either males or females ages 18-55. The controlled variable is the location that the subjects will remain in. This will be a carefully monitored area where ambient temperature, sleeping and waking hours will be the same,......

Words: 549 - Pages: 3

Free Essay

Lab 1 Security and Fundamentals Lab

...Lab 1 assessment worksheet 1. Name at least five applications and tools pre-loaded on the windows 2003 server target vm Windows applications loaded start as services y/n Filezilla y Wireshark n Nessus server n Nessus client n N map zen map n Mozilla fire fox n 2. What was the dhcp allocated source ip host address for the student vm, dhcpp server and ip default gateway router? 172.30.0.10 172.30.0.11 172.30.0.1 3. did the targeted ip host respond to the icmp echo-request with an icmp echo-reply packet when you iniated the ping command at your dos prompt? If yes how many icmp echo-request packets were sent back to the ip source? Yes 12 3 host 4.If you ping the windows target 01 vm server and the Ubuntu target 01 vm server which fields in the icmp echo-request/ echo-replies vary? Ttl is 128.64 5. what is the command line syntax for running an intense scan with zen map on a target subnet of 172.30.0.0/24 N map t4 a v pe ps22,25,80 - pa21,23,80,3389, 172.30.0.0/24 6. name at least 5 different scans that may be performed from the zenmap gui and document under what circumstances you......

Words: 369 - Pages: 2

Premium Essay

Lab 1

...Lab 1: Input, Processing, and Output This lab accompanies Chapter 2 of Starting Out with Programming Logic & Design. Name: ___________________________ Lab 1.1 – Algorithms This lab requires you to think about the steps that take place in a program by writing algorithms. Read the following program prior to completing the lab. Write a program that will take in basic information from a student, including student name, degree name, number of credits taken so far, and the total number of credits required in the degree program. The program will then calculate how many credits are needed to graduate. Display should include the student name, the degree name, and credits left to graduate. Step 1: Examine the following algorithm. (Reference: Designing a Program, page 31). 1. Get the student name. 2. Get the degree program name. 3. Subtract the number of credits taken so far from the required credits for the degree. 4. Get the number of credits required for the degree program. 5. Get the number of credits the student has taken so far. 6. Display the input information in Step 1 and 2. 7. Display the calculated information. Step 2: What logic error do you spot and how would you fix it? Step 3: What steps require user interaction (Ex: user must type in some input)? Lab 1.2 – Pseudocode This lab requires you to think about the steps that take place in a program by writing pseudocode. Read the following......

Words: 2451 - Pages: 10

Premium Essay

Lab 1

...Lab Report 1: Pipettes and Std Curve Ingrid Simons University of Texas at El Paso June 12, 2014 Introduction: Procedures that require very small volumes of DNA and reagents are performed with instruments such as, micropipettes and pipettes. These instruments are used when scientists need to accurately and precisely deliver small volumes of a liquid. Molecular biologists use very small volumes of liquid at times they are as small as 0.1 µL, in order to do these measurements the use micropipettes. The function of the micropipettes is to act as a plunger when the depressed by the thumb and by its release liquid is drawn into a disposable plastic tip. The liquid is released when the plunger is pressed again (The University of QueensLand). The tip is an important part of the micropipette, each tip is disposable and come in different sizes depending of the micropipette being used. There is three standard micropipettes, the P20 which measures 0.5-20μL, P200 that measures 20-200 μL, and P1000 that measures 100 μL to 1 mL. An important part of this laboratory was learning how to read the meniscus curve. A meniscus is a curve that is formed at the surface of a molecular substance, such as water, when it touches another material (USGS). Meniscus is caused by adhesion, a result of water’s high surface tension. The glass beaker attracts water molecules, and water molecules stay together, as a result many molecules gather to touch the glass. They will accumulate along......

Words: 886 - Pages: 4

Free Essay

Lab#1

...IS 3220July 7, 2014 Lab #1 Analyze Essential TCP/IP Networking Protocols 1. What is the purpose of the address resolution protocol (ARP)? ARP is used to mediate between Ethernet (and other broadcast link-level protocols) and the network layer, or IP protocols. Put more simply, ARP converts IP addresses to Ethernet addresses. 2. What is the purpose of the dynamic host control protocol (DHCP)? DHCP (Dynamic Host Configuration Protocol) is a communications protocol that lets network administrators centrally manage and automate the assignment of Internet Protocol (IP) addresses in an organization's network. http://searchunifiedcommunications.techtarget.com/definition/DHCP/ARP. Lab #2 Network Documentation 1. When you TELNET to LAN Switch 1 and LAN Switch 2, why is it a good idea to first PING an IP interface or port’s IP address? The ping verifies connectivity by sending ICMP echo packets to a host and listening for an echo reply. This will detect if there are any name resolution issues. 2. Why is using Telnet a security risk for an IP network infrastructure? Telnet sessions are in clear text and programs such as packet sniff can capture passwords and then use them to log into those sessions. 3. How can you mitigate the security risk caused by Telnet? Intrusion detection is a packet inspection tool that monitors, intercepts and responds to abuse in real time. ICMP inspection permits responses to ICMP packets like ping and traceroute that come......

Words: 427 - Pages: 2

Premium Essay

Lab 1

...Laboratory #1 Lab #1: Evaluate Business World Transformation – Impact of the Internet and WWW Learning Objectives and Outcomes Upon completing this lab, students will be able to complete the following tasks: * Identify the security challenges on the web as they relate to various business models and the impact that is made in e-Commerce and Internet-based deployments * Extract various businesses’ personal identifiable information (PII) that is collected and stored from Internet users by a business in a web application * Distinguish among the different reasons for the attacks on web sites and determine exactly what the attackers are after when they target your WWW presence * Evaluate the current state of security on a LAMP server using Telnet, Skipfish and TCPdump to identify whether the proper tools are installed for a security evaluation of the server * Install and use Firefox Web Browser with the Live HTTP Headers plug-in Lab #1 – Compromised Business Application Impact Analysis Course Name & Number: ______________________________________________________________ Student Name: _______________________________________________________________________ Instructor Name: _____________________________________________________________________ Lab Due Date: _______________________________________________________________________ Overview The threats of the Internet go way beyond an attacker defacing your website. An attack can include......

Words: 849 - Pages: 4

Free Essay

Lab Report 1

...Equipment used in the Oceanographic Research Platforms in the Arctic region, the following observation and test were performed. The scenario is having Research equipment installed on the Research Platforms that can survive harsh marine environments while operating for long periods of time with little or no maintenance. The material used for these equipment are to be made of brass plate because it is good corrosion resistance, easy machining tough. The question seeking for an answer of the investigation is “Can buying brass ingot and roll it flat to get a 60 percent reduction in thickness and hardness of 45 without it cracking?” For this experiment, there was two test that was conducted, Cold Working test and the Heat Treatment Test, on a sample of 260 Brass in ingot form. For the Cold Working Test, the first done was putting the sample through a Stanat Rolling Mill to reduce the thickness of the ingot. Part two of the Cold Working Test was to use the Rockwell Hardness Tester to measure the hardness of Brass. Do this test ten times at increments of -0.75 from 10.5mm to 3mm. At each targeted thickness, measure the width and length. The result of the test is on Table 1. After doing the Cold working Test, Heat treatment test is done. For this test, take the 3mm brass plate and cut it into 5 equal pieces and place each piece into the5 furnaces at 100°C, 260°C, 350°C, 450°C, and 565°C. Test the Hardness of each piece on the Rockwell Hardness Tester and the results are on Table 2.......

Words: 1903 - Pages: 8

Free Essay

Physics Lab on Mechanics

...Wind is very essential If the experiment is being done directly under an air vent the ball would go much faster as there is extra downward force affecting time . Wind should be consistent throughout all the experiment trials . If the ball is heavy than it would fall much faster than a lighter ball so all experiment trials should have the same mass and this would mean to have the same type of ball. Suppose the ball was made out of rubber , it would have much more air resistance and will slow the time of the ball. Independent Variables-Distance at which the height is dropped Dependent Variables- The time of how long it takes for the ball to drop from Point A to B Diagram Equipment • Stopwatch (±0.01s) • Ball(same mass and same type of ball) • 1 meter ruler (± 0.05cm) • 3 meter tape Method • • • • • First measure the distance ,Start with a height of 0.3m Accurately time the ball when released and time the ball when it hits the ground Then , Increase the height by 0.3m and repeat step 2 Take a minimum of three trials of each reading to improve accuracy Take an average of the readings and then using the formulae and the graph find the value of Gravity Calculation(Raw Data) Distance   0.3m 0.6m 0.9m 1.2m 1.5m 1.8m 2.1m 2.4m   Average   Time1(s)   Time2(s)   Time3(s)   Average   Acceleration +  0.01   +  0.01   +  0.01   Time(s)   m.s-­‐2     (2s/t2)   +  0.01   0.22 0.23 0.22 0.22 12.39 0.34 0.33 0.35 0.34 10.38 0.46 0.47 0.43 0.45 8.89......

Words: 1334 - Pages: 6

Free Essay

Grit Test- Lab 1

...Grit Test- Lab 1 On the scale of 1 to 5, my grit test score was a 2.57, I gave every answer my time and was full honest but for some reason it just doesn’t make much sense. This test of grit is supposed to measures conscientiousness courage, excellence, resilience, and endurance versus perfection. In the courage part when it talks about fear of failure is described as, “a debilitating disorder characterized by an unhealthy aversion to risk. Some symptoms include anxiety, mental blocks, and perfectionism…” Even though I don’t think I have a disorder I’m pretty conscious with the fact that I do have a fear of failure. In fact, when it comes to perfectionism, I end up spending more time on the final presentation and every little detail rather than focus on the excellence of a project. Age is a very important in determining level of grit in a population. Individual experience about when being persistent allows you to figure out which things are worth doing. It may be worth someone you may be paying for services or solution to a problem, but it may not be worth pursuing a modeling career at the age of 30 and being 60 pounds overweight. Learning to pick my fights is not a reflection of my grittiness, but somewhat realistic of the human condition, which is almost always disappointing. Most of the tips listed on ways to improve grit said I was “realistic optimist” (Jotski, K.). This worked for me a couple quarters back when I chose to be the leader for a debate. ...

Words: 312 - Pages: 2

Free Essay

Nutrition Lab #1

...NUTRITION 121 HUMAN NUTRITION LABORATORY BACKGROUND AND METHODS MODULE #1 BODY COMPOSITION Late Labs: 10 point deduction! A report submitted >1 week late, will receive 0 points for the lab!! Written and edited by: Karon Felten and Nutrition 121 TA’s With Special Thanks to: Chris Pritsos Ph.D. Nutrition Department Chairman ABSTRACT: In nutrition, there are many factors that influence an individual’s health and body weight, such as heredity, food selection, eating behaviors, and physical activity. Scale weight is not always a good indicator of body fat, lean mass, body water or overall health (1). This laboratory experience will give students the opportunity to conduct physical assessments by evaluating body weight and body composition. To determine body weight and body composition, techniques such as bioelectrical impedance analysis (BIA), body mass index (BMI), waist circumference, wrist circumference for determining frame size, and a scale will be utilized. Students will also evaluate their own risk for cardiovascular disease and assess cardiovascular health in volunteers by measuring heart rate, filling out a heart disease risk score form, and estimating oxygen consumption and energy expenditure through a technique known as the Queens College Three-Minute Step Test. BACKGROUND: Your body is made up of the six essential nutrients: water, fat, protein, carbohydrates and various vitamins and minerals. Many factors can influence an......

Words: 4204 - Pages: 17

Premium Essay

Lab 1

...Unit 1 Labs Lab 1.1 Step 13 Lab 1.2 Define Major Topics for a Database NOUNS | MAJOR TOPIC | Doctors | Patients | Drugs | Side Effects | Researchers | Patient Information | Westlake Research Hospital | Conducting test of new Depression Drugs | Lab 1.3 Create a Statement of Work Scope The Software-Tracking database will be used to help manage the school’s software licensing. The software will be monitored for lifecycle and version corrections as well as keeping track of the number of users accessing the software under the constraints of the license agreement. The faculty and staff computers will be tracked for which version and licensed copy of software is currently running on each system. Constraints The database can be used for accessing the faculty and staff’s logon to the school employee website for the purpose of inputting and updating hours worked. Faculty and staff members can conduct business related work, such as adjusting work schedules, and student’s grades in the system but are not able to view student’s personal files in the registrars system. Objectives * Make for a more efficient system by allowing employees to have control of shared calendars and student’s grades. * Improve the tracking of Software Licensing and the Lifecycle of programs. Tasks and Timeline 1. Gathering Data: Meet with School Board and those involved to discuss the needs and wants for a database. Time Allotted: 3 weeks. Deliverables: A list of......

Words: 365 - Pages: 2

Przygodowe | Dark Figure of Crime (2018) HDRip Movie Watch Online Free | Spider-Man- Homecoming (2017) [1080p] English